Improved Analysis on the Fin Reliability of a Plate Fin Heat Exchanger for Usage in LNG Applications

Mustansar Hayat Saggu, Nadeem Ahmed Sheikh, Usama Muhamad Niazi, Muhammad Irfan, Adam Glowacz and Stanislaw Legutko
Additional contact information
Mustansar Hayat Saggu: Department of Mechanical Engineering, International Islamic University, Islamabad 44000, Pakistan
Nadeem Ahmed Sheikh: Department of Mechanical Engineering, International Islamic University, Islamabad 44000, Pakistan
Usama Muhamad Niazi: Mechanical Engineering Department, Universiti Teknologi PETRONAS, Seri Iskandar 32610, Perak, Malaysia
Muhammad Irfan: Electrical Engineering Department, College of Engineering, Najran University, Najran 61441, Saudi Arabia
Adam Glowacz: Department of Automatic, Control and Robotics, AGH University of Science and Technology, 30-059 Kraków, Poland
Stanislaw Legutko: Faculty of Mechanical Engineering and Management, Poznan University of Technology, 3 Piotrowo Street, 60-965 Poznan, Poland

Energies, 2020, vol. 13, issue 14, 1-16

Abstract: A plate fin heat exchanger (PFHE) is a critical part of the cryogenic industry. A plate fin heat exchanger has many applications, but it is commonly used in the liquefied natural gas (LNG) industry for the gasification/liquefaction process. During this gasification to the liquefaction process, there is a large temperature gradient. Due to this large temperature gradient, stresses are produced that directly influence the braze joint of PFHE. Significant work has been carried out on heat transfer and the flow enhancement of PFHE; however, little attention has been paid to structural stability and stresses produced in these brazed joints. Due to these stresses, leakages in PFHE are observed, mostly in braze joints. In the current study, standard fin design is analyzed. In addition, the structural stability of brazed joints under standard conditions is also tested. Two techniques are used here to analyze fins, using the finite element method (FEM), first by examining the whole fin brazed joint on the basis of experimentally calculated yield strength and second by dividing the braze seam into three sections and defining individual strength for each section of the seam to find stress magnitude on the basis of heat-affected zones. Moreover, by using two different techniques to analyze brazed joints, the stresses in the lower face of the brazed joint were increased by 13% and decreased by 18% in the upper face using different zone techniques as compared to standard full braze seam analysis. It can be concluded that different zone techniques are better in predicting stresses as compared to simple full braze seam analysis using the finite element method since stresses along the lower face are more critical.

Keywords: plate fin heat exchanger; structural stability; stresses; symmetric design structure; symmetrical heating plates; mechanical properties; factor of safety (search for similar items in EconPapers)
JEL-codes: Q Q0 Q4 Q40 Q41 Q42 Q43 Q47 Q48 Q49 (search for similar items in EconPapers)
Date: 2020
References: View references in EconPapers View complete reference list from CitEc
Citations: View citations in EconPapers (2)

Downloads: (external link)
https://www.mdpi.com/1996-1073/13/14/3624/pdf (application/pdf)
https://www.mdpi.com/1996-1073/13/14/3624/ (text/html)

Related works:
This item may be available elsewhere in EconPapers: Search for items with the same title.

Export reference: BibTeX RIS (EndNote, ProCite, RefMan) HTML/Text

Persistent link: https://EconPapers.repec.org/RePEc:gam:jeners:v:13:y:2020:i:14:p:3624-:d:384332

Access Statistics for this article

Energies is currently edited by Ms. Agatha Cao

More articles in Energies from MDPI
Bibliographic data for series maintained by MDPI Indexing Manager ().