Next Generation Solar Cells Based on Graded Bandgap Device Structures Utilising Rod-Type Nano-Materials

Imyhamy M. Dharmadasa, Ayotunde A. Ojo, Hussein I. Salim and Ruvini Dharmadasa
Additional contact information
Imyhamy M. Dharmadasa: Materials and Engineering Research Institute, Sheffield Hallam University, Sheffield S1 1WB, UK
Ayotunde A. Ojo: Materials and Engineering Research Institute, Sheffield Hallam University, Sheffield S1 1WB, UK
Hussein I. Salim: Materials and Engineering Research Institute, Sheffield Hallam University, Sheffield S1 1WB, UK
Ruvini Dharmadasa: Conn Centre for Renewable Energy Research, University of Louiseville, Kentucky, KY 40292, USA

Energies, 2015, vol. 8, issue 6, 1-19

Abstract: Current solar cells under research and development utilise mainly one absorber layer limiting the photon harvesting capabilities. In order to develop next generation solar cells, research should move towards effective photon harvesting methods utilising low-cost solar energy materials. This will lead to reduce the $W ?1 figure for direct solar energy conversion to electrical energy. In this work, a graded bandgap solar cell has been designed to absorb all photons from the UV, visible and IR regions. In addition, impurity PV effect and impact ionisation have been incorporated to enhance charge carrier creation within the same device. This new design has been experimentally tested using the most researched MOCVD grown GaAs/AlGaAs system, in order to confirm its validity. Devices with high V oc ~ 1175 mV and the highest possible FF ~ (0.85–0.87) have been produced, increasing the conversion efficiency to ~20% within only two growth runs. These devices were also experimentally tested for the existence of impurity PV effect and impact ionisation. The devices are PV active in complete darkness producing over 800 mV, V oc indicating the harvesting of IR radiation from the surroundings through impurity PV effect. The quantum efficiency measurements show over 140% signal confirming the contribution to PV action from impact ionisation. Since the concept is successfully proven, the low-cost and scalable electrodeposited semiconducting layers are used to produce graded bandgap solar cell structures. The utilisation of nano- and micro-rod type materials in graded bandgap devices are also presented and discussed in this paper. Preliminary work on glass/FTO/n-ZnS/n-CdS/n-CdTe/Au graded bandgap devices show 10%–12% efficient devices indicating extremely high J sc values ~48 mA·cm ?2 , showing the high potential of these devices in achieving higher efficiencies. The detailed results on these low-cost and novel graded bandgap devices are presented in a separate publication.

Keywords: graded bandgap structures; next generation solar cells; impurity PV effect; impact ionisation; nano-materials (search for similar items in EconPapers)
JEL-codes: Q Q0 Q4 Q40 Q41 Q42 Q43 Q47 Q48 Q49 (search for similar items in EconPapers)
Date: 2015
References: View references in EconPapers View complete reference list from CitEc
Citations: View citations in EconPapers (4)

Downloads: (external link)
https://www.mdpi.com/1996-1073/8/6/5440/pdf (application/pdf)
https://www.mdpi.com/1996-1073/8/6/5440/ (text/html)

Related works:
This item may be available elsewhere in EconPapers: Search for items with the same title.

Export reference: BibTeX RIS (EndNote, ProCite, RefMan) HTML/Text

Persistent link: https://EconPapers.repec.org/RePEc:gam:jeners:v:8:y:2015:i:6:p:5440-5458:d:50766

Access Statistics for this article

Energies is currently edited by Ms. Agatha Cao

More articles in Energies from MDPI
Bibliographic data for series maintained by MDPI Indexing Manager ().