Sustainable High-Speed Milling of Magnesium Alloy AZ91D in Dry and Cryogenic Conditions
Nabil Jouini (),
Mohd Shahfizal Mohd Ruslan,
Jaharah A. Ghani and
Che Hassan Che Haron
Additional contact information
Nabil Jouini: Mechanical Engineering Department, College of Engineering, Prince Sattam Bin Abdulaziz University, Alkharj 11942, Saudi Arabia
Mohd Shahfizal Mohd Ruslan: Department of Mechanical and Manufacturing Engineering, Faculty of Engineering and Built Environment, Universiti Kebangsaan Malaysia, Bangi 43600, Selangor, Malaysia
Jaharah A. Ghani: Department of Mechanical and Manufacturing Engineering, Faculty of Engineering and Built Environment, Universiti Kebangsaan Malaysia, Bangi 43600, Selangor, Malaysia
Che Hassan Che Haron: Department of Mechanical and Manufacturing Engineering, Faculty of Engineering and Built Environment, Universiti Kebangsaan Malaysia, Bangi 43600, Selangor, Malaysia
Sustainability, 2023, vol. 15, issue 4, 1-14
Abstract:
Magnesium alloy AZ91D is used extensively in the automotive industry because of its high strength-to-weight ratio. Typically, components produced using the alloy are required to have good surface finish and to contribute to high productivity but require long cutting times. Cryogenic cooling is an environmentally friendly technology which has been proven to improve cutting tool life and surface finish. This paper presents an investigation on the effects of dry and cryogenic cutting conditions at a high cutting speed regime for milling of magnesium alloy. This study focused on a high-speed regime due to the chips of magnesium alloy being highly combustible and an effective means of decreasing the temperature in the cutting zone was of great concern. The machining experiment was carried out using uncoated carbide end milling utilizing a full factorial design (L16) with cutting speeds of 900 m/min and 1300 m/min, feed rate of 0.02 mm/tooth and 0.05 mm/tooth, axial depth of cut at 0.2 mm and 0.3 mm, and radial depth of cut at 10 mm and 40 mm. For dry machining, the longest tool life at flank wear (VBmax) of 0.21 mm was at 30 min, which was obtained at cutting speeds of 1300 m/min, feed rate of 0.02 mm/tooth, axial depth of cut at 0.2 mm, and radial depth of cut at 40 mm. Using this cutting condition, a mirror-like surface of 0.106 µm was produced. For machining under cryogenic condition at VBmax of 0.2 mm, the maximum tool life of 1864 min was achieved at a cutting speed of 900 m/min, feed rate of 0.02 mm/tooth, axial depth of cut of 0.3 mm, and radial depth of cut of 40 mm. Under this cutting condition, a lower surface finish of 0.091 µm was obtained. It can be concluded that the application of liquid nitrogen (LN2) is very effective in enhancing the tool life and in obtaining a better-machined surface, especially at a lower cutting speed of 900 m/min. A longer tool life and high-quality machined parts will significantly improve the productivity and cost savings in the related industry.
Keywords: tool wear; magnesium alloy AZ91D; surface roughness; high speed milling (search for similar items in EconPapers)
JEL-codes: O13 Q Q0 Q2 Q3 Q5 Q56 (search for similar items in EconPapers)
Date: 2023
References: View complete reference list from CitEc
Citations:
Downloads: (external link)
https://www.mdpi.com/2071-1050/15/4/3760/pdf (application/pdf)
https://www.mdpi.com/2071-1050/15/4/3760/ (text/html)
Related works:
This item may be available elsewhere in EconPapers: Search for items with the same title.
Export reference: BibTeX
RIS (EndNote, ProCite, RefMan)
HTML/Text
Persistent link: https://EconPapers.repec.org/RePEc:gam:jsusta:v:15:y:2023:i:4:p:3760-:d:1072750
Access Statistics for this article
Sustainability is currently edited by Ms. Alexandra Wu
More articles in Sustainability from MDPI
Bibliographic data for series maintained by MDPI Indexing Manager ().