IMPROVEMENT OF WEAR RESISTANCE OF SHREDDER BLADES USED IN A REFUSE-DERIVED FUEL (RDF) FACILITY BY PLASMA NITRIDING

Hakan Aydin and Furkan Bostanci
Additional contact information
Hakan Aydin: Mechanical Engineering Department, Engineering Faculty, Bursa Uludag University, 16059 Gorukle-Bursa, Turkey
Furkan Bostanci: #x2020;Tofas-Fiat, Turkish Automobile Factory Co., Bursa, Turkey

Surface Review and Letters (SRL), 2020, vol. 27, issue 04, 1-13

Abstract: Refuse-derived fuel (RDF) is a kind of renewable energy source to produce energy for replacement of fossil fuels. Aggressive working conditions in RDF facilities cause the shredder blades to wear out quickly. So, the purpose of this paper was to study the effect of plasma-nitriding process on wear resistance of shredder blades made of AISI D2 tool steel in the service condition of RDF facility. Shredder blades were commercially available from two different suppliers (A and B suppliers). These hardened shredder blades were plasma-nitrided in the mixed nitrogen and hydrogen atmosphere at a volume ratio of 3:1 at 450∘C for 12, 18 and 24h at a total pressure of 250 Pa. Characterisation of plasma-nitrided layers on the shredder blades was carried out by means of microstructure and microhardness measurements. Wear tests of plasma-nitrided shredder blades were performed under actual working conditions in the RDF facility. Wear analysis of these shredder blades was conducted using three-dimensional (3D) optical measuring instrument GOM ATOS II. The compositional difference of the shredder blades provided by A and B suppliers played an important role on the nitrided layer. The case depth of A-blades significantly increased with increasing plasma-nitriding time. However, the case depth of B-blades was fairly lower at the same nitriding time and only slightly increased with increasing plasma-nitriding time. Plasma-nitriding process significantly improved the surface hardness of the shredder blades. Maximum surface hardness values were achieved at nitriding time of 18 h for both blades. In this case, this increase in surface hardness values was above 100%. At nitriding time of 24h, the maximum surface hardness of A-blades significantly decreased, whereas this decrease in surface hardness of B-blades was the negligible value. The wear test results showed that plasma-nitriding process significatly decreased the wear of shredder blades; 18 h nitriding for A-blades and 24h nitriding for B-blades had better wear-reducing ability in the service condition of RDF facility. In these cases, the decreases in the total volume wear loss for A- and B-blades were 53% and 60%, respectively.

Keywords: Refuse-derived fuel facility; shredder blades; AISI D2 steel; compositional difference; plasma nitriding; microhardness; wear (search for similar items in EconPapers)
Date: 2020
References: View complete reference list from CitEc
Citations:

Downloads: (external link)
http://www.worldscientific.com/doi/abs/10.1142/S0218625X19501312
Access to full text is restricted to subscribers

Related works:
This item may be available elsewhere in EconPapers: Search for items with the same title.

Export reference: BibTeX RIS (EndNote, ProCite, RefMan) HTML/Text

Persistent link: https://EconPapers.repec.org/RePEc:wsi:srlxxx:v:27:y:2020:i:04:n:s0218625x19501312

Ordering information: This journal article can be ordered from

DOI: 10.1142/S0218625X19501312

Access Statistics for this article

Surface Review and Letters (SRL) is currently edited by S Y Tong

More articles in Surface Review and Letters (SRL) from World Scientific Publishing Co. Pte. Ltd.
Bibliographic data for series maintained by Tai Tone Lim ().