DRY SLIDING WEAR AND CORROSION BEHAVIOR OF AA7075–SiC COMPOSITES

S. Surendarnath, G. Ramesh and T. Ramachandran
Additional contact information
S. Surendarnath: Department of Mechanical Engineering, DVR & Dr. HS MIC College of Technology, Vijayawada 521180, Andhra Pradesh, India
G. Ramesh: ��Department of Metallurgical and Materials Engineering, Rajiv Gandhi University of Knowledge Technology, RK Valley, Kadapa 516330, Andhra Pradesh, India
T. Ramachandran: ��Department of Mechanical Engineering, Jain University, Bangalore 560069, Karnataka, India

Surface Review and Letters (SRL), 2025, vol. 32, issue 11, 1-12

Abstract: Automobile structural components are subject to high stress, friction and corrosive environmental conditions. Though aluminum alloys exhibit lightweight and high corrosion resistance, there is a need to improve the high strength-to-weight ratio and resistance to friction. This paper presents microstructural analysis, hardness, dry sliding wear behavior, and corrosion behavior of AA7075 reinforced with silicon carbide (SiC) particles. The composite specimens were prepared at the concentration of 2.5 and 5 wt.% SiC. The microstructure of AA7075 showed dendritic morphology while composite specimens showed nondendritic morphology grains. Reinforcement of SiC resulted in increased nucleation site and refinement of grain during solidification. XRD analysis of base alloy showed α matrix with η (MgZn2), T(Al–Zn–Mg–Cu) and Al7Cu2Fe phases, while the composite sample showed the presence of additional S(Al2CuMg) and θ (Al2Cu) phases. Composite samples showed higher hardness values than base alloy due to grain boundary strengthening and Orowan strengthening. The enhancement of hardness of AA7075 by 20% and 37.5% were obtained with the addition of 2.5 and 5 wt.% SiC particles respectively and also predicted with less coefficient of friction and less wear rate at all the tested load conditions. At the same time, the respective reduction in wear rates of AA7075 was found to be 50 and 65%. The worn-out surface of the base alloy was found to have undergone extensive plastic deformation and resulted in delamination with extensive patches and no clear groove marks. The composite sample of 2.5 wt.% SiC showed mild patches with clear groove marks, while the Composite of 5 wt.% SiC showed groove marks with fine width parallel to sliding directions. The wear mechanism was found to be transferred from adhesive mode to abrasive mode through a mixed mechanical layer with an added concentration of SiC particles from 0 wt.% to 5 wt.%. Weight loss during immersion corrosion increases with an increase in the amount of SiC due to an increased amount of metallic phase which increases microgalvanic corrosion and pitting. Hence, composite samples showed decreased corrosion resistance than base alloy.

Keywords: AA7075 alloy; SiC reinforcement; composite; microstructure; wear; corrosion (search for similar items in EconPapers)
Date: 2025
References: Add references at CitEc
Citations:

Downloads: (external link)
http://www.worldscientific.com/doi/abs/10.1142/S0218625X25500015
Access to full text is restricted to subscribers

Related works:
This item may be available elsewhere in EconPapers: Search for items with the same title.

Export reference: BibTeX RIS (EndNote, ProCite, RefMan) HTML/Text

Persistent link: https://EconPapers.repec.org/RePEc:wsi:srlxxx:v:32:y:2025:i:11:n:s0218625x25500015

Ordering information: This journal article can be ordered from

DOI: 10.1142/S0218625X25500015

Access Statistics for this article

Surface Review and Letters (SRL) is currently edited by S Y Tong

More articles in Surface Review and Letters (SRL) from World Scientific Publishing Co. Pte. Ltd.
Bibliographic data for series maintained by Tai Tone Lim ().