Research in Agricultural Engineering
2003 - 2025
Current editor(s): Bc. Michaela Polcarová From Czech Academy of Agricultural Sciences Bibliographic data for series maintained by Ivo Andrle (). Access Statistics for this journal.
Is something missing from the series or not right? See the RePEc data check for the archive and series.
Volume 59, issue SpecialIssue, 2013
- Comparison of thermal and rheologic properties of Slovak mixed flower honey and forest honey pp. S1-S8

- M. Božiková and P. Hlaváč
- Ammonia concentration in farrowing pens with permanent limited range of motion for lactating sows pp. S9-S14

- M. Dubeňová, R. Gálik, Š. Mihina and T. Šima
- Effect of crop residues on CO2 flux in the CTF system during soil tillage by a disc harrow Lemken Rubin 9 pp. S15-S21

- T. Šima and M. Dubeňová
- Gyroscope calibration with the method of simulated identification pp. S22-S26

- V. Cviklovič, D. Hrubý, M. Olejár and L. Priatková
- The operation of agricultural tractor with universal ecological oil pp. S27-S33

- J. Kosiba, Z. Tkáč, Ľ. Hujo, B. Stančík and I. Štulajter
- Application of differential geometry in agricultural vehicle dynamics pp. S34-S41

- J. Rédl and V. Váliková
- Hard machining of agricultural machines parts pp. S42-S48

- R. Drlička, J. Žarnovský, R. Mikuš, I. Kováč and M. Korenko
- I-x-w diagram of wet air and wheat grain pp. S49-S53

- I. Vitázek and J. Havelka
- Verification of agro-production building structures affecting the quality of indoor environment in the summer season pp. S54-S59

- Š. Pogran, T. Reichstadterová, J. Lendelová, D. Páleš, W. Bieda and M. Bošanský
- Selected properties of agricultural biomass pp. S60-S64

- V. Kažimírová, T. Brestovič and R. Opáth
- Determining the guidance system accuracy with the support of a large GNSS dataset pp. S65-S70

- V. Rataj, J. Galambošová and M. Vašek
Volume 59, issue 4, 2013
- Index of volume 59 pp. I-II

- Editors
- Selected physical properties of liquid biofuels pp. 121-127

- P. Trávníček, M. Valach, Z. Hlaváčová, J. Mareček, T. Vítěz and P. Junga
- Effect of destabilization treatment on microstructure, hardness and abrasive wear of high chromium hardfacing pp. 128-135

- R. Chotěborský and P. Hrabě
- Silage-corn harvesting machinery traffic effects on soil bulk density and water permeability pp. 136-140

- I. Ahmadi and H. Ghaur
- Soldering steel sheets using soft solders pp. 141-146

- M. Brožek
- Research of overlays influence on ploughshare lifetime pp. 147-152

- P. Hrabě and M. Müller
- Reliability of ZigBee transmission in agriculture production pp. 153-159

- I. Mašík
Volume 59, issue 3, 2013
- Evaluation of tractor biodegradable hydraulic fluids on the basis of hydraulic pump wear pp. 75-82

- R. Majdan, Z. Tkáč, J. Kosiba, R. Abrahám, J. Jablonický, Ľ. Hujo, M. Mojžiš, P. Ševčík and M. Rášo
- Chemical, stoichiometric and thermal analysis of fatty acid methyl esters from processed animal fat pp. 83-90

- J. Malaťák, L. Škarková and A. Prošková
- Analysis of ground massif temperatures with horizontal heat exchanger pp. 91-97

- M. Šeďová, R. Adamovský and P. Neuberger
- Disintegration process in disc crushers pp. 98-104

- P. Vaculík, J. Maloun, L. Chládek and M. Přikryl
- Determination of oxygen permeability of polyethylene and polypropylene nonwoven fabric foils pp. 105-113

- Ľ. Kubík and S. Zeman
- Computer simulation of the teat-cup liner stress and strain tensor pp. 114-119

- I. Karas, R. Gálik, Š. Pogran and M. Šesták
Volume 59, issue 2, 2013
- Experimental model of ammonia elimination by ozone in the air pp. 39-45

- P. Hutla, B. Petráčková and J. Kára
- Degradation of polymer particle systems in agrocomplex pp. 46-50

- P. Valášek and M. Brožek
- Comparison of three methods for rendering plant fat transesterification pp. 51-55

- A. Prošková, J. Kučera, Z. Kopicová and L. Škarková
- Evaluation of work quality of the green peas harvester Ploeger EPD 490 pp. 56-60

- P. Findura, J. Turan, J. Jobbágy, M. Angelovič and O. Ponjican
- Application of hard surfacing for repairing of agricultural parts pp. 61-67

- J. Viňáš, J. Brezinová, A. Guzanová and M. Kotus
- Analysis of the model application of mechanical equipment for hydrothermal treatment pp. 68-73

- P. Junga, T. Vítěz, P. Mach and P. Trávníček
Volume 59, issue 1, 2013
- LIST OF REVIEWERS 2012 pp. I

- Editors
- Optimization of anaerobic fermentation of kitchen waste pp. 1-8

- T. Dlabaja and J. Malaťák
- Analysis of tangential curve equation describing mechanical behaviour of rapeseeds (Brassica napus L.) mixture under compression loading pp. 9-15

- D. Herák, A. Kabutey and M. Divišová
- Overlay materials used for increasing lifetime of machine parts working under conditions of intensive abrasion pp. 16-22

- M. Müller and P. Hrabě
- Effect of heat treatment on the microstructure, hardness and abrasive wear resistance of high chromium hardfacing pp. 23-28

- R. Chotěborský
- Research into the geometry of the delimbing head of cutting knives pp. 29-34

- J. Mikleš
- Challenges of designing a cracker for Morama bean - Short communication pp. 35-37

- Z. Tjiparuro
Volume 58, issue 4, 2012
- Index of volume 58 pp. I-II

- Editors
- Evaluation of reed canary grass (Phalaris arundinacea L.) grown for energy use pp. 119-130

- Z. Strašil
- Determination of the technical parameters of shaping tools for delimbing head pp. 131-135

- M. Mikleš
- Optimisation of a clam bunk skidder from the emission production point of view pp. 136-141

- A. Janeček and R. Adamovský
- Ear tag mechanical properties under extreme climate conditions pp. 142-147

- M. Müller and D. Lukešová
- Analysis of strength ratio of different hop strings pp. 148-154

- P. Heřmánek, A. Rybka, I. Honzík, L. Vent, B. Jošt and J. Mašek
- Model for energy and deformation determination of selected oilseeds under compression loading - Short communication pp. 155-158

- A. Kabutey, D. Herák, R. Chotěborský and M. Navrátilová
Volume 58, issue 3, 2012
- Degradation medium of agrocomplex - adhesive bonded joints interaction pp. 83-91

- M. Müller and P. Valášek
- Effect of sedimentation on the final hardness of polymeric particle composites pp. 92-98

- P. Valášek, M. Müller and A. Proshlyakov
- Study and determination of energy consumption to produce conventional rice of the Guilan province pp. 99-106

- A. Alipour, H. Veisi, F. Darijani, B. Mirbagheri and A.G. Behbahani
- Bruise susceptibilities of kiwifruit as affected by impact and fruit properties pp. 107-113

- E. Ahmadi
- The coefficient of friction of individual potatoes and various handling materials - Short communication pp. 114-117

- C.F.H. Bishop, A.F.J. Gash, C. Heslim and S. Hanney
Volume 58, issue 2, 2012
- Effect of rapeseed methyl ester on fuel consumption and engine power pp. 37-45

- M. Pexa and K. Kubín
- Linseed harvests parameters depending on the state of cutting mechanism pp. 46-49

- J. Souček and D. Blažej
- Assessment of energy use pattern for tomato production in Iran: A case study from the Marand region pp. 50-56

- M.R. Jadidi, M.S. Sabuni, M. Homayounifar and A. Mohammadi
- Analysis of rock mass borehole temperatures with vertical heat exchanger pp. 57-65

- R. Adamovský, L. Mašek and P. Neuberger
- Influence of moisture content and loading orientation on some mechanical properties of Mucuna flagellipes nut pp. 66-72

- N.A. Aviara, O.A. Onuh and S.E. Ehiabhi
- Modeling some drying characteristics of garlic sheets under semi fluidized and fluidized bed conditions pp. 73-82

- R. Amiri Chayjan, K. Salari and B. Shadidi
Volume 58, issue 1, 2012
- Experimental testing of some types of biologically degradable materials for processing in the SBM mechanical plant for hydrothermal treatment pp. 1-8

- P. Junga, E. Krčálová, K. Somerlíková and J. Mareček
- Impact of different harvest times on ash fusibility of energy grasses pp. 9-15

- P. Hutla, P. Jevič, Z. Strašil and J. Kočica
- Drying of cherry tree chips in the experimental biomass dryer with solar collector pp. 16-23

- T. Ivanova, B. Havrland, P. Hutla and A. Muntean
- Mechanical behaviour of several layers of selected plant seeds under compression loading pp. 24-29

- D. Herák, A. Kabutey, A. Sedláček and G. Gűrdil
- Quality evaluation of briquettes made from wood waste pp. 30-35

- M. Brožek, A. Nováková and M. Kolářová
| |