Research in Agricultural Engineering

2003 - 2025

Current editor(s): Bc. Michaela Polcarová

From Czech Academy of Agricultural Sciences
Bibliographic data for series maintained by Ivo Andrle ().

Access Statistics for this journal.
Is something missing from the series or not right? See the RePEc data check for the archive and series.

2011, volume 57, articles SpecialIssue

Analysis of the relations between some physicalindicators of market eggs pp. S1-S6

R. Gálik, Z. Poláková, Š. Boďo and M. Denker

Using satellite navigation for seeding of wide-row and narrow-row crops pp. S7-S13

M. Macák, M. Žitňák and L. Nozdrovický

Evaluation of efficiency of precision irrigation for potatoes pp. S14-S23

J. Jobbágy, J. Simoník and P. Findura

Drying medium - modelling and process evaluation pp. S24-S29

I. Vitázek and J. Havelka

Comparison of numerical integration methods in strapdown inertial navigation algorithm pp. S30-S34

V. Cviklovič, D. Hrubý, M. Olejár and O. Lukáč

Operating parameters and emission evaluation of tractors running on diesel oil and biofuel pp. S35-S42

D. Müllerová, M. Landis, I. Schiess, J. Jablonický and M. Prístavka

The comparison of biodegradable hydraulic fluid with mineral oil on the basis of selected parameters pp. S43-S49

R. Majdan, J. Kosiba, J. Tulík, D. Kročková and V. Šinský

Influence of welding method on microstructural creation of welded joints pp. S50-S56

P. Čičo, D. Kalincová and M. Kotus

Measurement of titanium surface roughness created by non-conventional cutting technology pp. S57-S60

J. Rusnák, M. Zeleňák, J. Valíček, M. Kadnár, S. Hloch, P. Hlaváček, M. Kušnerová, R. Čep and J. Kadnár

Material machining for friction knots of moving parts for agricultural machines pp. S61-S68

J. Žitňanský, J. Žarnovský, R. Mikuš, I. Kováč and Z. Andrássyová

Shadow method for the evaluation of surface created by hydroabrasive dividing of materials pp. S69-S73

J. Valíček, M. Kadnár, P. Hlaváček, J. Rusnák, S. Hloch, M. Zeleňák, M. Řepka, M. Kušnerová and J. Kadnár

Analysis of wear resistent weld materials in laboratory conditions pp. S74-S78

M. Kotus, Z. Andrássyová, P. Čičo, J. Fries and P. Hrabě

2011, volume 57, articles 4

List of reviewers Index of volume 57 pp. I-II

Editors

The use of CAN-Bus messages of an agricultural tractor for monitoring its operation pp. 117-127

J. Čupera and P. Sedlák

A novel three-point hitch dynamometer to measure the draft requirement of mounted implements pp. 128-136

M. Askari, M.H. Komarizade, A.M. Nikbakht, N. Nobakht and R.F. Teimourlou

Biogas composition depending on the type of plant biomass used pp. 137-143

M. Herout, J. Malaťák, L. Kučera and T. Dlabaja

Design and development of power operated banana slicer for small scale food processing industries pp. 144-152

S.P. Sonawane, G.P. Sharma and A.C. Pandya

Influence of surface integrity on bonding process pp. 153-162

M. Müller

2011, volume 57, articles 3

Analysis of force effects measured in the tractor three-point linkage pp. 79-87

J. Čupera, F. Bauer, L. Severa and M. Tatíček

An analysis of energy use, input costs and relation between energy inputs and yield of apple orchard pp. 88-96

R. Fadavi, A. Keyhani and S.S. Mohtasebi

Ambient temperature kinetic assessment of biogas production from co-digestion of horse and cow dung pp. 97-104

M.O.L. Yusuf, A. Debora and D.E. Ogheneruona

Change of mechanical properties in substrate during rewelding deposit pp. 105-109

R. Chotěborský, P. Hrabě and A. Kabutey

A mathematical model for predicting the cracking efficiency of vertical-shaft centrifugal palm nut cracker pp. 110-115

M.C. Ndukwu and S.N. Asoegwu

2011, volume 57, articles 2

Heat-emission analysis of small combustion equipments for biomass pp. 37-50

J. Malaťák and L. Passian

Sensors connection for yield determination on round balers with variable chamber pp. 51-55

M. Kroulík, J. Mašek, Z. Kvíz, B. Jošt and V. Prošek

Effects of MIG process parameters on the geometry and dilution of the bead in the automatic surfacing pp. 56-62

R. Chotěborský, M. Navrátilová and P. Hrabě

Technical-economical indicators in the sugar beet transportation management pp. 63-71

M. Žitňák and M. Korenko

Behaviour of different moisture contents of Jatropha curcas L. seeds under compression loading pp. 72-77

A. Kabutey, D. Herák and A. Sedláček

2011, volume 57, articles 1

Measurements of tractor power parameters using GPS pp. 1-7

M. Pexa, M. Cindr, K. Kubín and V. Jurča

Threshing force of paddy as affected by loading manner and grain position on the panicle pp. 8-12

M.R. Alizadeh and A. Allameh

Tangent curve utilization for description of mechanical behaviour of pressed mixture pp. 13-18

D. Herák, A. Kabutey, A. Sedláček and G. Gűrdil

Drying sage (Salvia officinalis L.) in passive solar dryers pp. 19-29

A.A. Hassanain

Content changes of adsorbable organically bound halogens during sludge centrifugation and drying pp. 30-36

K. Hrich and B. Groda

LIST OF REVIEWERS 2010 pp. X1

Editors

2010, volume 56, articles 4

Index of Volume 56 pp. I-II

Editors

Frequency of occurrence of a certain air temperature at various sites in the Czech Republic pp. 127-137

V. Šleger and P. Neuberger

The usage of CAN-Bus messages for engine power determination pp. 138-146

J. Čupera and T. Šmerda

Microbial contamination of the sand from the wastewater treatment plants pp. 147-153

M. Szostková and T. Vítěz

Particle size distribution of sawdust and wood shavings mixtures pp. 154-158

T. Vítěz and P. Trávníček

Determination of loading capacity depending on bevel angle of the wooden bonded scarf joint pp. 159-165

O. Dajbych, D. Herák, A. Sedláček and G. Gűrdil

2010, volume 56, articles 3

Study of knotweed (Reynoutria) as possible phytomass resource for energy and industrial utilization pp. 85-91

Z. Strašil and J. Kára

Light and noise conditions of buildings for breeding dairy cows pp. 92-98

M. Šístková, A. Peterka and B. Peterka

Study on some engineering attributes of pine nut (Pinus pinea) to the design of processing equipment pp. 99-106

S.M.T. Gharibzahedi, V. Etemad, J. Mirarab-Razi and M. Fos'hat

Influence of top link length of three-point hitch on performance parameters of ploughing set pp. 107-115

J. Čupera and T. Šmerda

The durability test of tractor hydrostatic pump type UD 25 under operating load pp. 116-121

Š. Drabant, J. Kosiba, J. Jablonický and J. Tulík

Lipase-catalyzed transesterification of rendering plant fat - Short Communication pp. 122-125

A. Prošková, Z. Kopicová, J. Kučera and L. Škarková

2010, volume 56, articles 2

Influence of engine power and shifting mode on energy-performance parameters of tractor's set pp. 47-52

J. Čupera and T. Šmerda

Design of hoppers using spreadsheet pp. 53-58

C.O.C. Oko, E.O. Diemuodeke and I.S. Akilande

Dimensioning of the bonded lap joint pp. 59-68

M. Müller and D. Herák

Modeling of heat and entropy sorption of maize (cv. Sc704): neural network method pp. 69-76

R.A. Chayjan and M. Esna-Ashari

Functional performance of a vertical-shaft centrifugal palm nut cracker pp. 77-83

M.C. Ndukwu and S.N. Asoegwu

2010, volume 56, articles 1

Tracked mechanism simulation of mobile machine in MSC.ADAMS/View pp. 1-7

J. Matej

Exploitation of anaerobic fermentation of bio-degradable wastes pp. 8-17

J. Kára, E. Janča and D. Herák

The accelerated laboratory test of biodegradable fluid type "ertto" pp. 18-25

Z. Tkáč, R. Majdan, Š. Drabant, J. Jablonický, R. Abrahám and P. Cvíčela

An ultrasound based technique for the determination of poultry egg quality pp. 26-32

M. Aboonajmi, A. Akram, T. Nishizu, N. Kondo, S.K. Setarehdan and A. Rajabipour

Modeling the mass of Iranian export onion (Allium cepa L.) varieties using some physical characteristics pp. 33-40

R. Ghabel, A. Rajabipour, M. Ghasemi-Varnamkhasti and M. Oveisi

The influence of conductivity measurement on mechanical properties of potato tubers - Short communication pp. 41-46

J. Blahovec and A. Yurov