|
|
Energy
1976 - 2025
Current editor(s): Henrik Lund and Mark J. Kaiser From Elsevier Bibliographic data for series maintained by Catherine Liu (). Access Statistics for this journal.
Is something missing from the series or not right? See the RePEc data check for the archive and series.
Volume 138, issue C, 2017
- A modified ammonia-water power cycle using a distillation stage for more efficient power generation pp. 1-11

- X. Chen, R.Z. Wang, L.W. Wang and S. Du
- Energy and exergy analysis of adiabatic compressed air energy storage system pp. 12-18

- Lukasz Szablowski, Piotr Krawczyk, Krzysztof Badyda, Sotirios Karellas, Emmanuel Kakaras and Wojciech Bujalski
- Multi-objective demand response to real-time prices (RTP) using a task scheduling methodology pp. 19-31

- Tomás Cortés-Arcos, José L. Bernal-Agustín, Rodolfo Dufo-López, Juan M. Lujano-Rojas and Javier Contreras
- Effect of a real steam turbine on thermoeconomic analysis of combined cycle power plants pp. 32-47

- Carlo Carcasci, Lorenzo Cosi, Riccardo Ferraro and Beniamino Pacifici
- Co-liquefaction of whole Jatropha curcas seed and glycerol using deep eutectic solvents as catalysts pp. 48-59

- Y. Alhassan, H.S. Pali, N. Kumar and I.M. Bugaje
- Primary energy evaluation of heat pumps considering dynamic boundary conditions in the energy system pp. 60-78

- Sebastian Stinner, Tim Schlösser, Kristian Huchtemann, Dirk Müller and Antonello Monti
- Estimation of technical and economic potential of offshore wind along the coast of India pp. 79-91

- Garlapati Nagababu, Surendra Singh Kachhwaha and Vimal Savsani
- Simultaneous coordination of distinct plug-in Hybrid Electric Vehicle charging stations: A modified Particle Swarm Optimization approach pp. 92-102

- S. Suganya, S. Charles Raja and P. Venkatesh
- Performances of grooved plates falling film absorber pp. 103-117

- Benoit Michel, Nolwenn Le Pierrès and Benoit Stutz
- A unified modeling framework for lithium-ion batteries: An artificial neural network based thermal coupled equivalent circuit model approach pp. 118-132

- Qian-Kun Wang, Yi-Jun He, Jia-Ni Shen, Zi-Feng Ma and Guo-Bin Zhong
- An energy-efficient method for direct-contact ultrasonic cloth drying pp. 133-138

- Chang Peng, Ayyoub M. Momen and Saeed Moghaddam
- The effect of floor insulation on indoor air temperature and energy consumption of residential buildings in moderate climates pp. 139-146

- Anna Staszczuk, Magdalena Wojciech and Tadeusz Kuczyński
- Open-cell foams for thermoacoustic applications pp. 147-156

- Marialuisa Napolitano, Rosario Romano and Raffaele Dragonetti
- Fabrication and characterization of novel shape-stabilized synergistic phase change materials based on PHDA/GO composites pp. 157-166

- Rui-rui Cao, Xuan Li, Sai Chen, Hao-ran Yuan and Xing-xiang Zhang
- Dominant flow structure in the squealer tip gap and its impact on turbine aerodynamic performance pp. 167-184

- Zhengping Zou, Fei Shao, Yiran Li, Weihao Zhang and Albin Berglund
- A scenario based approach to designing electricity grids with high variable renewable energy penetrations in Ontario, Canada: Development and application of the SILVER model pp. 185-196

- Madeleine McPherson and Bryan Karney
- Experimental investigation of autoignition of hydrogen-air charge in a compression ignition engine under dual-fuel mode pp. 197-209

- V. Chintala and K.A. Subramanian
- Mathematical modeling and evolutionary generation of rule sets for energy-efficient flexible job shops pp. 210-227

- Liping Zhang, Qiuhua Tang, Zhengjia Wu and Fang Wang
- Comparison between Fanger's thermal comfort model and human exergy loss pp. 228-237

- Matjaž Prek and Vincenc Butala
- Improving energy and environmental performance of coal fuelled boilers – A new type of centrifugal dust separator with external flue recycle pp. 238-248

- R. Kubica, W. Mokrosz and A. Szlęk
- Modeling the operation of a thermoacoustic engine pp. 249-256

- Krzysztof Rogoziński, Iwona Nowak and Grzegorz Nowak
- A critical review on the simulations of wind turbine aerodynamics focusing on hybrid RANS-LES methods pp. 257-289

- Jesse Thé and Hesheng Yu
- Semi-analytical model for a geothermal system considering the effect of areal flow between dipole wells on heat extraction pp. 290-305

- Bisheng Wu, Guangqing Zhang, Xi Zhang, Robert G. Jeffrey, James Kear and Tongtiegang Zhao
- Model-based predictive maintenance in building automation systems with user discomfort pp. 306-315

- Nathalie Cauchi, Karel Macek and Alessandro Abate
- Modelling and simulation of an alkaline electrolyser cell pp. 316-331

- Z. Abdin, C.J. Webb and E.MacA. Gray
- A tool for assessing the energy demand and efficiency of machining systems: Energy benchmarking pp. 332-347

- Wei Cai, Fei Liu, Jun Xie, Peiji Liu and Junbo Tuo
- Process modeling and optimization for torrefaction of forest residues pp. 348-354

- Quang-Vu Bach, Øyvind Skreiberg and Chul-Jin Lee
- A hybrid evolutionary algorithm for secure multi-objective distribution feeder reconfiguration pp. 355-373

- Ali Azizivahed, Hossein Narimani, Ehsan Naderi, Mehdi Fathi and Mohammad Rasoul Narimani
- Hydrogenation improvement of TiFe by adding ZrMn2 pp. 375-382

- Peng Lv and Jacques Huot
- Turbulent diffusion flames of a low-calorific value syngas under varying turbulator angles pp. 383-393

- Mustafa Ilbas and Serhat Karyeyen
- Application of imputation techniques and Adaptive Neuro-Fuzzy Inference System to predict wind turbine power production pp. 394-404

- Majid Morshedizadeh, Mojtaba Kordestani, Rupp Carriveau, David S.-K. Ting and Mehrdad Saif
- New district heating system based on natural gas-fired boilers with absorption heat exchangers pp. 405-418

- Fangtian Sun, Jinzi Zhao, Lin Fu, Jian Sun and Shigang Zhang
- Performance and cost evaluation of an innovative Pumped Thermal Electricity Storage power system pp. 419-436

- Alberto Benato
- Modeling and performance evaluation of PEM fuel cell by controlling its input parameters pp. 437-445

- Sudarshan L. Chavan and Dhananjay B. Talange
- Optimum parameter design for performance of methanol steam reformer combining Taguchi method with artificial neural network and genetic algorithm pp. 446-458

- Kwan Ouyang, Horng-Wen Wu, Shun-Chieh Huang and Sheng-Ju Wu
- Assessment of off-design performance of a Kalina cycle driven by low-grade heat source pp. 459-472

- Jianyong Wang, Jiangfeng Wang, Yiping Dai and Pan Zhao
- Estimation of biomass higher heating value (HHV) based on the proximate analysis by using iterative neural network-adapted partial least squares (INNPLS) pp. 473-479

- Soleiman Hosseinpour, Mortaza Aghbashlo, Meisam Tabatabaei and Mehdi Mehrpooya
- Investigating the consistency and quality of EPC ratings and assessments pp. 480-489

- David Jenkins, Sophie Simpson and Andrew Peacock
- Thermoeconomic investigation of power utilities: Intercooled recuperated gas turbine cycle featuring cooled turbine blades pp. 490-499

- Mithilesh Kumar Sahu and Sanjay,
- A comparative analysis of wave power in the nearshore by WAM estimates and in-situ (AWAC) measurements. The case study of Varkiza, Athens, Greece pp. 500-508

- S. Foteinis, J. Hancock, N. Mazarakis, T. Tsoutsos and C.E. Synolakis
- Implementation of reduced-order physics-based model and multi-parameters identification strategy for lithium-ion battery pp. 509-519

- Zhongwei Deng, Hao Deng, Lin Yang, Yishan Cai and Xiaowei Zhao
- Advanced control strategy on battery storage system for energy management and bidirectional power control in electrical networks pp. 520-528

- Reza Hemmati and Neda Azizi
- Novel shortcut optimization model for regenerative steam power plant pp. 529-541

- Maojian Wang, Guilian Liu and Chi Wai Hui
- A high efficient semi-open system for fresh water production from atmosphere pp. 542-551

- J.Y. Wang, R.Z. Wang, L.W. Wang and J.Y. Liu
- Performance and reduction potential of energy and CO2 emissions among the APEC's members with considering the return to scale pp. 552-562

- Zhaohua Wang, Weijun He and Bo Wang
- Managing technology performance risk in the strategic design of biomass-based supply chains for energy in the transport sector pp. 563-574

- Federico d'Amore and Fabrizio Bezzo
- The effects of variable renewable electricity on energy efficiency and full load hours of fossil-fired power plants in the European Union pp. 575-589

- Mats de Groot, Wina Crijns-Graus and Robert Harmsen
- Experimental analysis of a coiled stirred tank containing a low cost PCM emulsion as a thermal energy storage system pp. 590-601

- M. Delgado, A. Lázaro, J. Mazo, C. Peñalosa, J.M. Marín and B. Zalba
- Selection of energy conservation projects through Financial Pinch Analysis pp. 602-615

- Pritam Sankar Roychaudhuri, Vasiliki Kazantzi, Dominic C.Y. Foo, Raymond R. Tan and Santanu Bandyopadhyay
- Critical analysis of the energy performance indicators for road lighting systems in historical towns of central Italy pp. 616-628

- Francesco Leccese, Giacomo Salvadori and Michele Rocca
- An assessment of Spain's new alternative energy support framework and its long-term impact on wind power development and system costs through behavioral dynamic simulation pp. 629-646

- A.S. Ibanez-Lopez and B.Y. Moratilla-Soria
- Landfill gas-powered atmospheric water harvesting for oilfield operations in the United States pp. 647-658

- Enakshi D. Wikramanayake, Onur Ozkan and Vaibhav Bahadur
- Effects of high-pressure anaerobic digestion up to 30 bar on pH-value, production kinetics and specific methane yield pp. 659-667

- Andreas Lemmer, Wolfgang Merkle, Katharina Baer and Frank Graf
- Solar thermal modeling for rapid estimation of auxiliary energy requirements in domestic hot water production: Proportional flow rate control pp. 668-681

- António Araújo and Vítor Pereira
- Experimental investigation of the effects of using metal-oxides/water nanofluids on a photovoltaic thermal system (PVT) from energy and exergy viewpoints pp. 682-695

- Mohammad Sardarabadi, Mohammad Hosseinzadeh, Arash Kazemian and Mohammad Passandideh-Fard
- Durability investigation and performance study of hydrothermal synthesized platinum-multi walled carbon nanotube nanocomposite catalyst for proton exchange membrane fuel cell pp. 696-705

- Farokh Mirzaei, Mohammad Javad Parnian and Soosan Rowshanzamir
- Design and optimization of a novel cryogenic Rankine power generation system employing binary and ternary mixtures as working fluids based on the cold exergy utilization of liquefied natural gas (LNG) pp. 706-720

- Feier Xue, Yu Chen and Yonglin Ju
- Analyzing the effects of real income and biomass energy consumption on carbon dioxide (CO2) emissions: Empirical evidence from the panel of biomass-consuming countries pp. 721-727

- Eyup Dogan and Roula Inglesi-Lotz
- Modeling and analysis of short-period transient response of a single, planar, anode supported, solid oxide fuel cell during load variations pp. 728-738

- Marko Nerat
- Entransy dissipation-based thermal resistance optimization of slab LHTES system with multiple PCMs arranged in a 2D array pp. 739-751

- Huiru Wang, Zhenyu Liu and Huiying Wu
- Experimental characterization and comparison of performance parameters of S-rotors for standalone wind power system pp. 752-763

- Bilawal A. Bhayo and Hussain Al-Kayiem
- State of charge estimation of lithium-ion batteries using a grey extended Kalman filter and a novel open-circuit voltage model pp. 764-775

- Haihong Pan, Zhiqiang Lü, Weilong Lin, Junzi Li and Lin Chen
- Reusable nitrogen-doped mesoporous carbon adsorbent for carbon dioxide adsorption in fixed-bed pp. 776-784

- A.L. Yaumi, M.Z. Abu Bakar and B.H. Hameed
- Utilization of Menteş iron ore as oxygen carrier in Chemical-Looping Combustion pp. 785-798

- Nesibe Dilmaç, Ömer Faruk Dilmaç and Esra Yardımcı
- Demand side management approach to rural electrification of different climate zones in Indian state of Tamil Nadu pp. 799-815

- J. Vishnupriyan and P.S. Manoharan
- A novel wind speed estimator-integrated pitch control method for wind turbines with global-power regulation pp. 816-830

- Dongran Song, Jian Yang, Mei Su, Anfeng Liu, Zili Cai, Yao Liu and Young Hoon Joo
- Investment in the energy sector: An optimization model that contemplates several uncertain parameters pp. 831-845

- Maria Laura Cunico, Julio Rolando Flores and Aldo Vecchietti
- Energy use implications of different design strategies for multi-storey residential buildings under future climates pp. 846-860

- Uniben Yao Ayikoe Tettey, Ambrose Dodoo and Leif Gustavsson
- Economic dispatch of multiple energy carriers pp. 861-872

- Soheil Derafshi Beigvand, Hamdi Abdi and Massimo La Scala
- Synthesis and study of metal-based oxygen carriers (Cu, Co, Fe, Ni) and their interaction with supported metal oxides (Al2O3, CeO2, TiO2, ZrO2) in a chemical looping combustion system pp. 873-882

- Mansour Mohammedramadan Tijani, Aqsha Aqsha and Nader Mahinpey
- Magnetic conductive polymer-graphene nanocomposites based supercapacitors for energy storage pp. 883-889

- Mahir Ozan Yanik, Ekrem Akif Yigit, Yahya Erkan Akansu and Ertugrul Sahmetlioglu
- Integrated energy security assessment pp. 890-901

- Juozas Augutis, Ričardas Krikštolaitis, Linas Martišauskas, Sigita Pečiulytė and Inga Žutautaitė
- Estimating the maximum energy-saving potential based on IT load and IT load shifting pp. 902-909

- Kai Zhu, Zhuo Cui, Yabo Wang, Hailong Li, Xiaojing Zhang and Carsten Franke
- An integrated approach for the installation of a wave farm pp. 910-919

- N. Arean, R. Carballo and G. Iglesias
- An exergy-based study on the relationship between costs and environmental impacts in power plants pp. 920-928

- Yolanda Lara, Fontina Petrakopoulou, Tatiana Morosuk, Alicia Boyano and George Tsatsaronis
- Experimental investigation on the heat transfer performance of a latent thermal energy storage device based on flat miniature heat pipe arrays pp. 929-941

- Yanhua Diao, Yameng Kang, Lin Liang, Yaohua Zhao and Tingting Zhu
- Exergy assessment of a rotary kiln-electric furnace smelting of ferronickel alloy pp. 942-953

- W. Rong, B. Li, Philip Liu and F. Qi
- A general model for the optimization of energy supply systems of buildings pp. 954-966

- E. Iturriaga, U. Aldasoro, A. Campos-Celador and J.M. Sala
- Wind speed description and power density in northern Spain pp. 967-976

- Cristina Herrero-Novoa, Isidro A. Pérez, M. Luisa Sánchez, Ma Ángeles García, Nuria Pardo and Beatriz Fernández-Duque
- A new chaotic time series hybrid prediction method of wind power based on EEMD-SE and full-parameters continued fraction pp. 977-990

- Cong Wang, Hongli Zhang, Wenhui Fan and Ping Ma
- Co-optimized trading of wind-thermal-pumped storage system in energy and regulation markets pp. 991-1005

- Mustafa S. Al-Swaiti, Ali T. Al-Awami and Mohammad Waqas Khalid
- New framework for optimal scheduling of combined heat and power with electric and thermal storage systems considering industrial customers inter-zonal power exchanges pp. 1006-1015

- Mohsen Kia, Mehrdad Setayesh Nazar, Mohammad Sadegh Sepasian, Alireza Heidari and João P.S. Catalão
- Semi-industrial continuous band microwave dryer for energy and exergy analyses, mathematical modeling of paddy drying and it's qualitative study pp. 1016-1029

- Hassan Jafari, Davood Kalantari and Mohsen Azadbakht
- From technology pathways to policy roadmaps to enabling measures – A multi-model approach pp. 1030-1041

- E. Mulholland, F. Rogan and B.P. Ó Gallachóir
- Risk assessment of power transmission network failures in a uniform pricing electricity market environment pp. 1042-1055

- Islam Abdin, Yan-Fu Li and Enrico Zio
- Parametric study on the distribution of flow rate and heat sink utilization in cooling channels of advanced aero-engines pp. 1056-1068

- Yuguang Jiang, Yaxing Xu, Silong Zhang, Khaled Chetehouna, Nicolas Gascoin, Jiang Qin and Wen Bao
- Cryogenics-based energy storage: Evaluation of cold exergy recovery cycles pp. 1069-1080

- Sarah Hamdy, Tatiana Morosuk and George Tsatsaronis
- Therblig-embedded value stream mapping method for lean energy machining pp. 1081-1098

- Shun Jia, Qinghe Yuan, Jingxiang Lv, Ying Liu, Dawei Ren and Zhongwei Zhang
- Environmental impacts of PV technology throughout the life cycle: Importance of the end-of-life management for Si-panels and CdTe-panels pp. 1099-1111

- Michela Vellini, Marco Gambini and Valentina Prattella
- Surrogate worth trade-off method for multi-objective thermal power load dispatch pp. 1112-1123

- Nirbhow Jap Singh, J.S. Dhillon and D.P. Kothari
- Joint train scheduling optimization with service quality and energy efficiency in urban rail transit networks pp. 1124-1147

- Yeran Huang, Lixing Yang, Tao Tang, Ziyou Gao and Fang Cao
- Analytic modeling of parabolic trough solar thermal power plants pp. 1148-1156

- Germán A. Salazar, Naum Fraidenraich, Carlos Antonio Alves de Oliveira, Olga de Castro Vilela, Marcos Hongn and Jeffrey M. Gordon
- Costs and impacts of potential energy strategies for rural households in developing communities pp. 1157-1174

- Nordica A. MacCarty and Kenneth Mark Bryden
- Degradation prediction of PEM fuel cell using a moving window based hybrid prognostic approach pp. 1175-1186

- Daming Zhou, Fei Gao, Elena Breaz, Alexandre Ravey and Abdellatif Miraoui
- Investigation of the effect of aluminum porous fins on heat transfer pp. 1187-1198

- K. Bilen, S. Gok, A.B. Olcay and I. Solmus
- Practical failure recognition model of lithium-ion batteries based on partial charging process pp. 1199-1208

- Kunlong Chen, Fangdan Zheng, Jiuchun Jiang, Weige Zhang, Yan Jiang and Kunjin Chen
- Sustainable urban heat strategies: Perspectives from integrated district energy choices and energy conservation in buildings. Case studies in Torino and Stockholm pp. 1209-1220

- C. Delmastro, F. Martinsson, J. Dulac and S.P. Corgnati
- Identification and thermodynamic analysis of reaction pathways of methylal and OME-n formation pp. 1221-1246

- Ralf Peters
- Optimization modeling for smart operation of multi-source district heating with distributed variable-speed pumps pp. 1247-1262

- Hai Wang, Haiying Wang, Zhou Haijian and Tong Zhu
- Reduction of process steam demand and water-usage through heat integration in sugar and ethanol production from sugarcane – Evaluation of different plant configurations pp. 1263-1280

- Eduardo A. Pina, Reynaldo Palacios-Bereche, Mauro F. Chavez-Rodriguez, Adriano V. Ensinas, Marcelo Modesto and Silvia A. Nebra
- Multi-objective optimization of a sugarcane biorefinery for integrated ethanol and methanol production pp. 1281-1290

- Juliana Q. Albarelli, Sandro Onorati, Priscilla Caliandro, Emanuela Peduzzi, M Angela A. Meireles, François Marechal and Adriano V. Ensinas
| | |
|